How To Build a Bird Feeder Gazebo

Cut out the gazebo pieces

Start by cutting the top and bottom panels and six walls. First, cut two 12-1/2 inch by 14-1/2 inch rectangles out of 3/4-in. plywood. Most home centers will cut the plywood to size for you. Mark, then cut off the corners as shown in above and in Figure A (linked at the end of this post).

Save six of the triangles, which will become the roof rafters of this wooden bird feeder a few minutes down the road. Use a jigsaw (or a circular saw) to cut six 10 inch wall sections from a 1×8 cedar board (actual width, 7-1/4 inches).

Family Handyman

Make a template

Next, make a template for the wall cutouts out of 1/2-in. plywood. It will take a few minutes, but it will make cutting out the rest of the wall sections easy once it’s finished.

To make your wall template, photocopy the pattern in Figure A and glue it onto a thin piece of plywood (or trace it on using carbon paper). Then use a 1/2-in. bit to drill pilot holes and the tops of the hearts, and a jigsaw to cut out the window opening and the tips of the hearts. Use two small nails to tack your template to one of the wall sections. Trace the window opening and use the template as a guide to drill the window pilot holes and the top-of-heart holes.

Tip: Use a brad point or Forstner bit to drill the holes for the window corners and hearts. They’ll create a cleaner cut and stay on course better than a standard twist drill bit.

Family Handyman

Draw the hearts and cut

Remove the template and mark the 45-degree angle heart tips with an angle square (they’re hard to mark accurately through the template). Finish cutting out the window openings and hearts with a jigsaw. Repeat this five more times!

Family Handyman

Assemble gazebo walls

Since each side of the hexagonal top and bottom is 7-1/4 inches long and the 1×8 cedar sides are also 7-1/4 inches wide, the pieces fit like a glove. Use 6d (2-inch-long) galvanized nails to secure each wall section to the top and bottom panels.

Family Handyman

Assemble the rafters

Take the six triangular corner cutoffs you made earlier and glue and nail them to the top hexagon to serve as rafters. Center each triangle on the layout lines and make sure the outer tips meet the outer corners of the cedar walls.

Family Handyman

Cut shingles

Use three overlapping layers of 1×6 cedar lap siding for the shingles. Use a protractor to draw the 65-degree angle on the siding, then a jigsaw with the bevel angle set at 10 degrees to cut the first six roof panels.

Family Handyman

Shingle the roof

Set the first row of siding in place, but don’t nail anything quite yet. Adjust the panels so they all hang over the walls the same distance and fit pretty uniformly on the rafters. Don’t worry too much about an exact fit since the plywood top will keep the water out. And with an open-air design, some wind-blown rain is bound to creep in anyway.

Use an electric brad nailer to install the roof panels; 1-in. hand-driven brads work fine, too. Then, cut, fit and nail on the second and third rows the same way.

Family Handyman

Add trim and hardware

Cut 7/8-in. dowels and nail them on the corners. Use galvanized screws to mount a pipe flange to the center of the base. Drill two more 1/2-in. holes about 3 in. apart and cut out the space between them to create a clean-out slot. Make the flap for the clean-out slot from a piece of scrap siding and secure it with one screw. Add a few 3/16-in. holes in the base for drainage.

Finally, bury a length of threaded pipe 16 in. into the ground, screw the pipe flange and bird feeder onto it and fill it up with bird seed. Dinner is served!

Family Handyman

Wooden Bird Feeder Plans and Project PDFs

Click the links below to download the construction drawing for this project.

Figure A